Standard ASME B16.9 wraps in several parameters that act as a guideline for the manufacturer of wrought factory-made buttwelding fittings such as elbows, tees, reducers including the ASME B16.9 Reducer etc. The fittings need to conform to the values of the following parameters i.e. overall concentric pipe reducer dimensions, ratings, testing, tolerances, and markings. Depending on the buyer, these reducers are made available between the size range of DN 15 to DN 1200. A reducer is a fitting component used in piping systems that aids the worker to reduce the size of the flow from large to small by reducing the size of the pipe. This being said, there are two kinds of reducers produced. One of which is a concentric reducer.
ASME B16.9 Reducer
Stainless Steel Concentric Reducer
Malleable Pipe Reducer
Schedule 80 Concentric Reducer
Cast Iron Concentric Reducer
Carbon Steel Reducer
A concentric ASME B16.9 Reducer is cone shaped, which gradually decreases around the pipe. In instances where there is a possibility of accumulation of air, the reducer results in cavitation. Often, the ASME B16.9 Concentric reducer is a part of high strength building metal materials as well as vertical piping systems. Usually, Stainless Steel Concentric reducer exhibit superior resistance to pitting, stress related corrosion cracking and oxidation. As typical of stainless steels, they could be used in a wide range of environmental settings without losing their high mechanical properties such as tensile strength and hardness along with good creep resistance. However, one must note that the properties of different stainless steel grades differ from each other, so the selection of the material must be done according to the application these reducers are to be used for.
ANSI B16.9 Concentric reducer Manufacturer
Standards | ANSI/ ASME B16.9, MSS-SP-43, BS4504, BS1560, BS4504, BS10 |
---|---|
Size Range | ½” NB to 24″ NB in (DN6~DN100) 10s, Sch 40s, Schedule 80s, 160s, XXS. |
size |
|
Various Type Concentric Reducer Type B | DN15 – DN1200 |
Manufacturing process | Push, Press, Forge, Cast, etc. |
Thickness | SCH20, SCH10, SCH30, SCH60, STD SCH40, XS, SCH 80, Schedule 100, SCH 120, SCHEDULE 140, SCH. 160, XXS available with NACE MR 01-75 |
Reducer Types | Seamless / Welded / ERW / Fabricated |
Butt Weld Concentric Pipe Reducer, ANSI B16.9, SCH 40, DN150 X DN50
ASTM A197 Concentric Reducer, NPT Ends
ASTM A234 Concentric Reducer, SCH 80 / 160
ASME B16.9 Concentric Reducer, A403 WP304L, DN100 X DN50, SCH 80S
Concentric Reducer, 16×10 Inch BW, ANSI B16.9, A234 WPB
ANSI B36.19 Concentric Reducer, A234 WP91, DN400 X DN350, BE
Seamless Concentric Reducer, Carbon Steel, A234 WPB, SCH 40
LTCS Concentric Reducer, ASTM A420 WPL6
Concentric Reducer, ASME B16.9, SCH 60
S31803 Concentric Reducer, SCH 160
Concentric Reducer, 1/2-56 Inch, CS, SS
ASTM A234 WPB Concentric Reducer, ANSI B16.9, BW Ends
Concentric Reducer, ANSI B16.9, DN150 x DN80, SCH 40, BW
Reducer Conc, ASTM A403 WP316L, 6 X 4 Inch
Steel Reducer, ASTM A234 WPB, 56 Inch
SS304 Concentric Reducer, SMLS, 2 X 1 Inch
SCH 80S Concentric Reducer, ASME B16.9, A403 WP304L, DN200 X DN150
Carbon Steel CC Reducer, SCH XXS, BW
Pipe Concentric Reducer, BW, ASTM A234 WPB
ASTM A234 Concentric Reducer, 16 × 10 Inch, BW Ends
Seamless Concentric Reducer, ASTM A234 WPB, DN200 X DN80, SCH 40
ASTM A815 Reducer, Duplex-SS, SCH 80, PE
Zinc Coating Reducer, 36 X 18 Inch, ANSI B16.5
DN150 X DN80 Concentric Reducer, ASTM A234 WPB, SCH 80, BE
SCH40 Pipe Reducer, ANSI B16.9, BW
Butt Welded Reducer, WPB, DN150 X DN50
Concentric Reducer, Stainless Steel SS304
ASTM A106 Gr.B Concentric Pipe Reducer, DN80 X DN50, Butt Weld
Stainless Steel Reducer, SS304, MSS SP-43
ASTM A234 WPB Concentric Reducer, BW, 6 IN X 3 IN
ANSI B16.9 Reducer, ASTM A234 WPB, SCH 80, DN150 X DN80
BW End Con. Reducer, ASTM A234 WPB, 4 X 2IN, SCH 40
Stainless Steel | ASTM A403 WP Gr. 304, 304H, 309, 310, 316, 316L, 317L, 321, 347, 904L |
Carbon Steel | ASTM A 234 WPB , WPBW, WPHY 42, WPHY 46, WPHY 52, WPH 60, WPHY 65 & WPHY 70. |
Duplex Steel | ASTM A 815, ASME SA 815 UNS NO S31803, S32205. Werkstoff No. 1.4462 |
Nickel Alloy | ASTM / ASME SB 336 UNS 2200 ( NICKEL 200 ), UNS 2201 (NICKEL 201 ), UNS 4400 (MONEL 400 ), UNS 8020 ( ALLOY 20 / 20 CB 3, UNS 8825 INCONEL (825), UNS 6600 (INCONEL 600 ), UNS 6601 ( INCONEL 601 ), UNS 6625 (INCONEL 625), UNS 10276 ( HASTELLOY C 276 ) |
Low Temperature Carbon Steel | ASTM A420 WPL3, A420 WPL6 |
Alloy Steel | ASTM / ASME A/SA 234 Gr. WP 1, WP 5, WP 9, WP 11, WP 12, WP 22, WP 91 |
Code RCD REISO | Ø BIG | Ø SMALL | HEIGHT H mm | THEORETICAL WEIGHT KG | ||||
---|---|---|---|---|---|---|---|---|
DN | D mm | Thickness S mm | DN | d mm | Thickness s mm | |||
27 21 | 3/4 | 26.9 | 2.3 | 1/2 | 21.3 | 2.0 | 38 | 0.08 |
33 21 | 1 | 33.7 | 2.6 | 1/2 | 21.3 | 2.0 | 50 | 0.09 |
33 27 | 3/4 | 26.9 | 2.3 | 0.09 | ||||
42 21 | 1″1/4 | 42.4 | 2.6 | 1/2 | 21.3 | 2.0 | 50 | 0.12 |
42 27 | 3/4 | 26.9 | 2.3 | 0.13 | ||||
42 33 | 1 | 33.7 | 2.6 | 0.14 | ||||
*48 21 | 1″1/2 | 48.3 | 2.6 | 1/2 | 21.3 | 2.0 | 64 | 0.18 |
48 27 | 3/4 | 26.9 | 2.3 | 0.19 | ||||
48 33 | 1 | 33.7 | 2.6 | 0.20 | ||||
48 42 | 1″1/4 | 42.4 | 2.6 | 0.20 | ||||
60 27 | 2 | 60.3 | 2.9 | 3/4 | 26.9 | 2.3 | 76 | 0.30 |
60 33 | 1 | 33.7 | 2.6 | 0.31 | ||||
60 42 | 1″1/4 | 42.4 | 2.6 | 0.32 | ||||
60 48 | 1″1/2 | 48.3 | 2.6 | 0.33 | ||||
76 33 | 2″1/2 | 76.1 | 2.9 | 1 | 33.7 | 2.6 | 90 | 0.40 |
76 42 | 1″1/4 | 42.4 | 2.6 | 0.47 | ||||
76 48 | 1″1/2 | 48.3 | 2.6 | 0.48 | ||||
76 60 | 2 | 60.3 | 2.6 | 0.49 | ||||
89 42 | 3 | 88.9 | 3.2 | 1″1/4 | 42.4 | 2.6 | 90 | 0.55 |
89 48 | 1″1/2 | 48.3 | 2.6 | 0.61 | ||||
89 60 | 2 | 60.3 | 2.9 | 0.62 | ||||
89 76 | 2″1/2 | 76.1 | 2.9 | 0.63 | ||||
114 48 | 4 | 114.3 | 3.6 | 1″1/2 | 48.3 | 2.6 | 100 | 0.85 |
114 60 | 2 | 60.3 | 2.9 | 0.98 | ||||
114 76 | 2″1/2 | 76.1 | 2.9 | 1.00 | ||||
114 89 | 3 | 88.9 | 3.2 | 1.02 | ||||
139 60 | 5 | 139.7 | 4.0 | 2 | 60.3 | 2.9 | 127 | 1.60 |
139 76 | 2″1/2 | 76.1 | 2.9 | 1.70 | ||||
139 89 | 3 | 88.9 | 3.2 | 1.74 | ||||
139 114 | 4 | 114.3 | 3.6 | 1.76 | ||||
*168 76 | 6 | 168.3 | 4.5 | 2″1/2 | 76.1 | 2.9 | 140 | 2.60 |
168 89 | 3 | 88.9 | 3.2 | 2.70 | ||||
168 114 | 4 | 114.3 | 3.6 | 2.82 | ||||
168 139 | 5 | 139.7 | 4.0 | 2.94 | ||||
219 114 | 8 | 219.1 | 6.3 | 4 | 114.3 | 3.6 | 152 | 5.03 |
219 139 | 5 | 139.7 | 4.0 | 5.12 | ||||
219 168 | 6 | 168.3 | 4.5 | 5.18 | ||||
*273 114 | 10 | 273.0 | 6.3 | 4 | 114.3 | 3.6 | 178 | 7.00 |
*273 139 | 5 | 139.7 | 4.0 | 7.20 | ||||
273 168 | 6 | 168.3 | 4.5 | 7.40 | ||||
273 219 | 8 | 219.1 | 6.3 | 7.55 | ||||
323 168 | 12 | 323.9 | 7.1 | 6 | 168.3 | 4.5 | 203 | 11.00 |
323 219 | 8 | 219.1 | 6.3 | 11.10 | ||||
323 273 | 10 | 273 | 6.3 | 11.20 |
ANSI B16.9 Concentric reducer Price in India | Concentric reducer Price in INR | ASME B16.9 Concentric reducer Price in USD | Pipe reducer Price in UAE Dirham |
STAINLESS STEEL SA 403 GR. WP316L DN 20X15 SCH10S CONCENTRIC REDUCER ASME AS PER ASME B16.9 BUTT Per Kg | Rs. 8,598 | US $115.61 | UAE Dirham 424.63 |
NPS | LBS | KG |
3/4-1/2 | 0.17 | 0.08 |
3/4-3/8 | 0.15 | 0.07 |
1-3/4 | 0.4 | 0.18 |
1-1/2 | 0.4 | 0.18 |
1.1/4-1 | 0.5 | 0.23 |
1.1/4-3/4 | 0.4 | 0.18 |
1.1/4-1/2 | 0.4 | 0.18 |
1.1/2-1.1/4 | 0.7 | 0.32 |
1.1/2-1 | 0.62 | 0.28 |
1.1/2-3/4 | 0.54 | 0.24 |
1.1/2-1/2 | 0.5 | 0.23 |
2-1.1/2 | 0.9 | 0.41 |
2-1.1/4 | 0.84 | 0.38 |
2-1 | 0.76 | 0.34 |
2-3/4 | 0.7 | 0.32 |
2.1/2-2 | 1.5 | 0.68 |
2.1/2-1.1/2 | 1.38 | 0.63 |
2.1/2-1.1/4 | 1.25 | 0.57 |
2.1/2-1 | 1.25 | 0.57 |
3-2.1/2 | 2 | 0.91 |
3-2 | 1.8 | 0.82 |
3-1.1/2 | 1.7 | 0.77 |
3-1.1/4 | 1.6 | 0.73 |
3.1/2-3 | 3.15 | 1.43 |
3.1/2-2.1/2 | 2.88 | 1.31 |
3.1/2-2 | 2.75 | 1.25 |
3.1/2-1.1/2 | 2.5 | 1.13 |
3.1/2-1.1/4 | 2.4 | 1.09 |
4-3.1/2 | 3.5 | 1.59 |
4-3 | 3.38 | 1.53 |
4-2.1/2 | 3.25 | 1.47 |
4-2 | 3 | 1.36 |
4-1.1/2 | 2.88 | 1.31 |
5-4 | 6 | 2.72 |
5-3.1/2 | 5.75 | 2.61 |
5-3 | 5.5 | 2.49 |
5-2.1/2 | 5.25 | 2.38 |
5-2 | 5 | 2.27 |
6-5 | 8.5 | 3.86 |
6-4 | 8.25 | 3.74 |
6-3.1/2 | 8.25 | 3.74 |
6-3 | 8 | 3.63 |
6-2.1/2 | 7.25 | 3.29 |
8-6 | 13.2 | 5.99 |
8-5 | 12 | 5.44 |
8-4 | 11 | 4.99 |
8-3.1/2 | 11 | 4.99 |
10-8 | 22 | 9.98 |
10-6 | 21.5 | 9.75 |
10-5 | 21 | 9.53 |
10-4 | 20 | 9.07 |
12-10 | 34 | 15.42 |
12-8 | 32 | 14.51 |
12-6 | 31 | 14.06 |
12-5 | 30 | 13.61 |
14-12 | 60 | 27.22 |
14-10 | 59.2 | 26.85 |
14-8 | 58.5 | 26.54 |
14-6 | 58 | 26.31 |
16-14 | 71 | 32.21 |
16-12 | 70 | 31.75 |
16-10 | 69.5 | 31.52 |
16-8 | 68.5 | 31.07 |
16-6 | – | – |
18-16 | 85 | 38.56 |
18-14 | 84 | 38.1 |
18-12 | 83 | 37.65 |
18-10 | 82 | 37.19 |
18-8 | – | – |
20-18 | 125 | 56.7 |
20-16 | 124 | 56.25 |
20-14 | 122 | 55.34 |
20-12 | 120 | 54.43 |
20-10 | – | – |
20-8 | – | – |
22-20 | 142 | 64.41 |
22-18 | 138 | 62.6 |
22-16 | 131 | 59.42 |
22-14 | 123 | 55.79 |
22-12 | – | – |
22-10 | – | – |
24-22 | – | – |
24-20 | 150 | 68.04 |
24-18 | 148 | 67.13 |
24-16 | 145 | 65.77 |
24-14 | – | – |
24-12 | – | – |
24-10 | – | – |
26-24 | 207 | 93.89 |
26-22 | 200 | 90.72 |
26-20 | 190 | 86.18 |
26-18 | 182 | 82.55 |
26-16 | – | – |
26-14 | – | – |
26-12 | – | – |
28-26 | 224 | 101.6 |
28-24 | 216 | 97.98 |
28-22 | 210 | 95.25 |
28-20 | 199 | 90.26 |
30-28 | 241 | 109.32 |
30-26 | 232 | 105.23 |
30-24 | 224 | 101.6 |
30-22 | 220 | 99.79 |
30-20 | 220 | 99.79 |
NPS | LBS | KG |
Nominal Pipe Size | 1/2 to 2.1/2 | 3 to 3.1/2 | 4 | 5 to 8 |
Outside Diameter at Bevel (D) |
+ 1.6 – 0.8 |
1.6 | 1.6 | + 2.4 – 1.6 |
Inside Diameter at End | 0.8 | 1.6 | 1.6 | 1.6 |
Overall Length (H) | 2 | 2 | 2 | 2 |
Nominal Pipe Size | 10 to 18 | 20 to 24 | 26 to 30 | 32 to 48 |
Outside Diameter at Bevel (D) |
+ 4 – 3.2 |
+ 6.4 – 4.8 |
+ 6.4 – 4.8 |
+ 6.4 – 4.8 |
Inside Diameter at End | 3.2 | 4.8 | + 6.4 – 4.8 |
+ 6.4 – 4.8 |
Overall Length (H) | 2 | 2 | 5 | 5 |
Wall Thickness (t) | Not less than 87.5% of Nominal Wall Thickness |