Socket Weld Flanges Manufacturer In India

ANSI b16.5 Stainless Steel Socket Weld Flange

Manufacturer of ASME b16.5 SWRF Flange, carbon steel socket weld flange

SS socket weld flange, ASME B16.5 Class 150 Socket weld Flanges exporter in Kuwait, Qatar

ANSI B16.5 Socket Weld Flanges

ANSI B16.5 Socket Weld Flanges

Stainless steel Socket Weld Flanges

Stainless steel Socket Weld Flanges

Carbon steel Socket Weld Flanges

Carbon steel Socket Weld Flanges

An ANSI socket weld flange is very similar in appearance to a Slip-On flange. The back side of this center opening is then counter bored to form the appropriate size socket to take the pipe outside diameter. steel socket weld flanges are available in pressure from 150# and up and pipe schedule 40 to schedule 160. When it comes to specifying the pipe schedule, it ensures that ID of the SW Flange matches the ID of pipe for smooth fluid flow.

In socket weld blind flange, the diameter of the smaller bore is the same as the inner diameter of the matching pipe. socket weld flange class 150 are primarily used to make flanged joints where required in small sizes in socket welded pipe specs.

The negative of this socket weld companion flange is that it can be more expensive than a slip-on due to more intricate machining, and they can be less readily available than slip-ons due to the fact that the bottom half of the inside diameter must be made to the same schedule as the pipe that is being used.

These socket weld RTJ flanges were initially developed for use on smaller sizes of pipe at higher pressure ratings.  They are more used on lower pressure temperature as well today.  DINESH INDUSTRIES offers these socket weld raised face flange in stainless and alloy material.

Ring joint socket weld flange contains a shoulder inside the flange that acts as a guide to set the depth at which the pipe is welded to the flange. They are fabricated by inserting the pipe end into the flange until it bottoms out against the shoulder, followed by retracting the pipe 1/8 inches before welding it in place. Aside from the fact that this practice was originally employed to reduce cracking due to thermal stresses in stainless steel superheaters, but over the years has become standard practice for the installation of all socket weld reducing flange.

Socket weld flange specifications

Product Type Socket Weld Flanges, SW forged Flange, Socket welding Flanges, ASME 16.5 Socket Weld Flanges / SWRF Flanges
Size ½” (15 NB) to 48″ (1200NB)
Class 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS, DIN Standard ND-6,10, 16, 25, 40 Etc.
Stainless Steel Socket Weld Flanges ASTM A182 F202 stainless steel, A240 F304 stainless steel, 304L stainless steel, 304H stainless steel, 316 stainless steel, 316L stainless steel, 316Ti stainless steel, 316LN stainless steel, 310S stainless steel, 317L stainless steel, 321 stainless steel, 410 stainless steel, 420 stainless steel, 440C stainless steel, 202 stainless steel, F904L stainless steel
Carbon Steel Socket Weld Flanges ASTM A105 Carbon, ASME SA105 Carbon, ASTM A350 Carbon, ASME A350 Carbon, ASTM A181 carbon, A516 gr 70 carbon, A694 F42 carbon, A694 F46 carbon, A694 F52 carbon, A694 F60 carbon, A694 F65 carbon
Alloy Steel Socket Weld Flanges ASTM / ASME A/SA 182 & A 387 F1, F5, F9, F11, F12, F22, F91
Duplex Steel Socket Weld Flanges ASTM / ASME A/SA 182 F 44, F 45, F51, F 53, F 55, F 60, F 61
Specialize As per drawing
Standard ANSI : ANSI B16.5, ANSI B16.47, MSS SP44, ANSI B16.36, ANSI B16.48 ,JIS,DIN,BS4504,SABS1123,EN1092-1, UNI,AS2129,GOST-12820DIN : DIN2527, DIN2566, DIN2573, DIN2576, DIN2641, DIN2642, DIN2655, DIN2656, DIN2627, DIN2628, DIN2629, DIN 2631, DIN2632, DIN2633, DIN2634, DIN2635, DIN2636, DIN2637, DIN2638, DIN2673B.S : BS4504 , BS4504, BS1560, BS10
Connection Type / Flange Face Type Ring Type Joint, Lap-Joint Face, Raised Face, Flat Face, Large Male-Female, Small Male-Female, Large Tongue & Groove, Small Tongue & Groove

 

Socket weld flange standard

  • ASTM A182 – ASME SA182 – Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings’
  • ASME B16.5– Pipe Flanges and Flanged Fittings’
  • MSS SP-6 – Standard Finishes for Contact Faces of Pipe Flanges and Connecting End Flanges of Valves and Fittings’

 

ANSI B16.5 socket weld flange material

Dimensions Base Material Pressure Rating
ASME B16.5 ASTM A182 (Forgings) ASTM A240 (Plate) 150#. 300#. 400#. 600#. 900#. 1500#. 2500#.
API 605 ASTM A182 (Forgings) ASTM A240 (Plate) 150#. 300#. 400#. 600#. 900#. 1500#. 2500#.
ASME B16.47series A & B ASTM A182 (Forgings) ASTM A240 (Plate) 150#. 300#. 400#. 600#. 900#. 1500#. 2500#.
EN1092-1 ASTM A182 (Forgings) PN2.5. PN6. PN10. PN16. PN25. PN40. PN63. PN100. PN160. PN250. PN320. PN400.
BS4504 BS970 (Bar)ASTM A240 (Plate) ASTM A182 (Forgings) PN2.5. PN6. PN10. PN16. PN25. PN40. PN63. PN100. PN160.
BS10 BS970 (Bar)ASTM A240 (Plate) ASTM A182 (Forgings)

Manufacturer of following types of socket weld flanges in India

ASTM A182 Stainless Steel F316 Socket Weld Flanges

ASTM A182 Stainless Steel F316 Socket Weld Flanges

ASTM A182 Stainless Steel F304L Socket Weld Flange

ASTM A182 Stainless Steel F304L Socket Weld Flange

Stainless Steel Socket Weld Flange

Stainless Steel Socket Weld Flange

Carbon Steel Socket Weld Flanges

Carbon Steel Socket Weld Flanges

Types of Socket weld Flanges

Stainless Steel Socket weld flanges Dimensions

  • Stainless Steel Class 150 Socket weld Flange
  • Stainless Steel Class 300 Socket weld Flange
  • Stainless Steel Class 600 Socket weld Flange
  • Stainless Steel Class 900 Socket weld Flange
  • Stainless Steel Class 1500 Socket weld Flange
  • Stainless Steel Class 2500 Socket weld Flange

ANSI ASME B16.5 Socket weld flanges Dimensions

  • ANSI ASME B16.5 Class 150 Socket weld Flanges
  • ANSI ASME B16.5 Class 300 Socket weld Flanges
  • ANSI ASME B16.5 Class 400 Socket weld Flanges
  • ANSI ASME B16.5 Class 600 Socket weld Flanges
  • ANSI ASME B16.5 Class 900 Socket weld Flanges
  • ANSI ASME B16.5 Class 1500 Socket weld Flanges
  • ANSI ASME B16.5 Class 2500 Socket weld Flanges
Carbon Steel Socket weld flanges Dimensions

  • Carbon Steel Class 150 Socket weld Flanges
  • Carbon Steel Class 300 Socket weld Flanges
  • Carbon Steel Class 600 Socket weld Flanges
  • Carbon Steel Class 900 Socket weld Flanges
  • Carbon Steel Class 1500 Socket weld Flanges
  • Carbon Steel Class 2500 Socket weld Flanges
High Nickel Alloy Socket weld Flanges

  • Hastelloy c276 Socket weld flanges
  • Nickel alloy 200 Socket weld flanges
  • Monel 400 Socket weld flanges
  • Inconel 625 Socket weld flanges
  • Incoloy 825 Socket weld flanges
  • Hastelloy b2 Socket weld flanges

ANSI B16.5 socket weld flange dimensions

ANSI ASME B16.5 Socket Weld Flanges Dimensions

150 lb socket weld flange dimensions

Drilling
Nominal Bore Socket Weld Dia.(D) Thick.(E) Dia.(F) Dia.(B) Dia.(A) Height1(H) Nbr Holes Dia.(C)
1/2″
90
11.2
35.05
30
22.2
14
4
15.87
60.3
3/4″
100
12.7
42.92
38
27.7
14
4
15.87
69.9
1″
110
14.3
50.80
49
34.5
16
4
15.87
79.4
1 1/4″
115
15.9
63.50
59
43.2
19
4
15.87
88.9
1 1/2″
125
17.5
73.15
65
49.5
21
4
15.87
98.4
2″
150
19.1
91.94
78
61.9
24
4
19.05
120.7
2 1/2″
180
22.3
104.65
90
74.6
27
4
19.05
139.7
3″
190
23.9
127.00
108
90.7
29
4
19.05
152.4
1,6mm raised face not included in the E & H dimensions

300# socket weld flange dimensions

Drilling
Nominal Bore Socket Weld Dia.(D) Thick.(E) Dia.(F) Dia.(B) Dia.(A) Height1(H) Nbr Holes Dia.(C)
1/2″
95
12.7
35.05
38
22.2
21
4
15.87
66.7
3/4″
115
14.3
42.92
48
27.7
24
4
19.05
82.6
1″
125
15.9
50.80
54
34.5
25
4
19.05
88.9
1 1/4″
135
17.5
63.50
64
43.2
25
4
19.05
98.4
1 1/2″
155
19.1
73.15
70
49.5
29
4
22.22
114.3
2″
165
20.7
91.94
84
61.9
32
8
19.05
127.0
2 1/2″
190
23.9
104.65
100
74.6
37
8
22.22
149.2
3″
210
27.0
127.00
117
90.7
41
8
22.22
168
1,6mm raised face not included in the E & H dimensions

600# socket weld flange dimensions

Drilling
Nominal Bore Socket Weld >Dia.(D) Thick.(E) Dia.(F) Dia.(B) Dia.(A) Height1(H) Nbr Holes Dia.(C)
1/2″
95
14.3
35.05
38
22.2
22
4
15.87
66.7
3/4″
115
15.9
42.92
48
27.7
25
4
19.05
82.6
1″
125
17.5
50.80
54
34.5
27
4
19.05
88.9
1 1/4″
135
20.7
63.50
64
43.2
29
4
19.05
98.4
1 1/2″
155
22.3
73.15
70
49.5
32
4
22.22
114.3
2″
165
25.4
91.94
84
61.9
37
8
19.05
127.0
2 1/2″
190
28.6
104.65
100
74.6
41
8
22.22
149.2
3″
210
31.8
127.00
117
90.7
46
8
22.22
168.3
6,4 raised face not included in the E & H dimensions

Manufacturing standard

ANSI, JIS, DIN, EN, BS4504, GOST etc.

Face

Raised Face (RF), Flat Face(FF), Ring-Type Joint (RTJ),Tongue-and-Groove (T&G), Male-and-Female (M&F)

Surface treatment

Anti Rust Oil, Black Paint Coating, Yellow Paint Coating, Hot Dipped Galvanized, Cold Galvanized, etc.

Pressure:
America Series: Class 150, Class 300, Class 600, Class 900A, Class 1500, Class 2500.
Europe Series: PN2.5, PN6, PN10, PN16, PN25, PN40, PN63, PN100, PN160, PN250, PN320, PN400.
Flange Material Carbon steel  ASTM A105. ASTM A350 LF1. LF2, CL1/CL2, A234, S235JRG2, P245GH
P250GH, P280GHM 16MN, 20MN ,20#
Stainless steel  ASTM A182, F304/304L, F316/316L
Alloy steel ASTM A182 A182 F12, F11, F22, F5, F9, F91etc.
Flange Standard                       ANSI Class 150 Flanges-Class 2500 Flanges
DIN 6Bar 10Bar 16Bar 25Bar 40Bar
JIS 5K Flanges-20K Flanges
UNI 6Bar 10Bar 16Bar 25Bar 40Bar
EN 6Bar 10Bar 16Bar 25Bar 40Bar

Stainless Steel and Carbon Steel Socket weld Flange Price List in India

Types of Socket weld flanges Price Unit
stainless steel Socket weld flanges class 150 $22.45 NOS
stainless steel Socket weld flanges class 300 $25.39 NOS
stainless steel Socket weld flanges class 600 $31.19 NOS
carbon steel Socket weld flanges class 150 $75.89 NOS
carbon steel Socket weld flanges class 300 $88.12 NOS
carbon steel Socket weld flanges class 600 $99.52 NOS
Socket weld flanges ansi b16 5 class 150 $75.56 NOS
Socket weld flanges ansi b16 5 class 300 $95.56 NOS

Available material and grades in socket weld flanges

  • 304 stainless steel socket weld flanges manufacturer
  • 304l stainless steel socket weld flange manufacturer
  • 304h stainless socket weld flange manufacturer
  • 316 stainless spectacle socket weld flange manufacturer
  • 317 stainless steel socket weld flange manufacturer
  • 321 stainless steel socket weld flange manufacturer
  • Stainless 300lb socket weld flange manufacturer
  • Stainless steel 900lb socket weld flange manufacturer
  • Stainless 2500lb socket weld flange manufacturer
  • Stainless 600lb socket weld flange manufacturer
  • Stainless 2500lb socket weld flange manufacturer
  • Stainless Steel socket weld flange manufacturer
  • Stainless spectacle socket weld flange manufacturer
  • Class 150 stainless socket weld flange manufacturer
  • Class 300 stainless socket weld flange manufacturer
  • Stainless 316 socket weld Flange manufacturer
  • Stainless Steel 321 class 150 socket weld flange manufacturer
  • Stainless Steel 316l socket weld flange manufacturer
  • Stainless 304l socket weld flange manufacturer
  • Stainless 900lb socket weld flange manufacturer
  • Stainless 304h socket weld flange manufacturer
  • Stainless 317 socket weld flange manufacturer
  • Stainless 316h socket weld flange manufacturer
  • stainless forged socket weld
  • stainless socket weld flange
  • socket weld flange stainless
  • 304 stainless spectacle flange
  • 316 stainless socket weld flange
  • 317 stainless socket weld flange
  • stainless 321 socket weld flange
  • stainless 316l socket weld flange
  • 304 stainless spectacle flange
  • 316 stainless forged socket weld flange
  • 317 stainless rtj socket weld flange
  • stainless 321 plate socket weld flange
  • stainless 321h socket weld flange
  • ASTM A105 carbon steel socket weld manufacturer
  • ASTM A350 carbon socket weld manufacturer
  • ASTM A182 lf2 carbon socket weld flange manufacturer
  • ASTM A694 F42 carbon socket weld flange manufacturer
  • ASTM A694 F46 carbon socket weld flange manufacturer
  • ASTM A694 F52 carbon socket weld flange manufacturer
  • ASTM A694 F60 carbon steel socket weld flange manufacturer
  • ASTM A694 F65 carbon socket weld flange manufacturer
  • ASTM A694 F70 carbon socket weld flange manufacturer
  • 321h Stainless steel 900lb socket weld flange manufacturer
  • 317 Stainless 1500lb socket weld manufacturer
  • Carbon steel socket weld manufacturer
  • Carbon steel socket weld manufacturer
  • A105 carbon steel socket weld manufacturer
  • A350 carbon steel socket weld manufacturer
  • A182 lf2 carbon steel socket weld manufacturer
  • A694 F42 carbon steel socket weld manufacturer
  • A694 F46 carbon socket weld manufacturer
  • A694 F52 carbon socket weld flange manufacturer
  • A694 F60 carbon socket weld flange manufacturer
  • A694 F65 carbon socket weld flange manufacturer
  • A694 F70 carbon steel spectacle flange manufacturer
  • carbon steel 300lb socket weld flange manufacturer
  • carbon 900lb socket weld flange manufacturer
  • carbon steel 2500lb socket weld flange manufacturer
  • carbon 600lb socket weld flange manufacturer
  • carbon 2500lb socket weld flange manufacturer
  • carbon forged socket weld flange
  • carbon socket weld flange
  • socket weld carbon flange
  • rtj carbon socket weld flange
  • spectacle carbon socket weld flange
  • forged carbon socket weld flange
  • carbon a105n socket weld flange
  • carbon a105 socket weld flange

We have ready stock available in following countries

MIDDLE EAST
Saudi Arabia
Kuwait
Jordan
Turkey
Iran
Iraq
Bahrain
Oman
Uae
Qatar
Yemen
Syria
AFRICA

Nigeria
Sudan
Algeria
Angola
Egypt
Equatorial Guinea
South Africa
Libya
The Republic Of Congo
Gabon

NORTH AMERICA

Jamaica
Costa Rica
Puerto Rica
Usa
Canada
Bahamas
Denmark
Mexico
Trinidad And Tobago

EUROPE

Russia
Uk
Norway
Spain
Portugal
Ireland
Croatia
Slovenia
Belgium
Hungary
Albania
Austria
Switzerland
Slovakia
Netherland
Greece
Czech Republic
Germany
France
Italy
Malta

ASIA

Japan
Sri Lanka
Maldives
Singapore
Malaysia
South Korea
Indonesia
India
Thailand
Vietnam
Mayanmar
Taiwan
Cambodia

SOUTH AMERICA

Brazil
Chile
Argentina
Bolivia
Ecuador
Paraguay
Venezuela
Colombia
Uruguay

Flat face socket weld flange, Socket weld blind flange supplier at best price in India

Ready stock of ANSI b16.5 class 150 socket-weld flanges, Socket weld flange as per customer requirement
Check ASME b16.5 reducing flange dimensions, Raised face socket weld flange dimensions

Comments are closed.